Results 1 to 9 of 9

Thread: Progress FAILED !!! on the programmer.

  1. #1
    Join Date
    Apr 2018
    Posts
    11
    Rep Power
    1

    Default Progress FAILED !!! on the programmer.

    Hello Guys;

    I have a problem, I can use Quartus Prime Lite Edition 15.1 so MY Project is created file that are .sof and .pof by Quartus Prime Lite Edition.

    I want to program my evaluation kit , I open programmer and set up hardware setup. I can look USB-Blaster-II and my evaluation kit property so

    I choose .sof file and click Start button. Progress is failed.

    Why did programmer occur error?
    WHAT should I do for programming file succesfully ??

    Thank u .

  2. #2
    Join Date
    Feb 2018
    Posts
    75
    Rep Power
    1

    Default Re: Progress FAILED !!! on the programmer.

    Hi,
    Provide details about evaluation Kit, Device & Error.
    Can you share a screenshot of the programmer?

    Best Regards
    Vikas Jathar
    (This message was posted on behalf of Intel Corporation)

  3. #3
    Join Date
    Apr 2018
    Posts
    11
    Rep Power
    1

    Default Re: Progress FAILED !!! on the programmer.

    Firstly, Thank u very much for reply ;

    I send print screens and my evaluation Kit is MAX10M50DAF484C6GES.
    My pc's software is Windows 10.

    Should I do different step ?

    I Dont understand why do error occur

    I hope u help me , ıt is very important for me
    Attached Images Attached Images

  4. #4
    Join Date
    Feb 2018
    Posts
    75
    Rep Power
    1

    Default Re: Progress FAILED !!! on the programmer.

    Hi,
    Perform the following steps,
    1. Visual check: Factory Default Switch and Jumper Settings, FPGA chip leads, LEDs status etc.
    2. To successfully use the USB-Blaster cable, disconnect it before power up the board. Once you power on the board, then reconnect the USB-Blaster cable.
    3. Open Quartus II Programmer
    4. Click Auto Detect(or else Check Add Device->select 10M50DAF484 )
    5. Add .sof file
    6. Turn on Program/Configure option.
    7. Click Start.
    8. Check the nSTATUS, CONF_DONE, nCONFIG signal status.




    Best Regards
    Vikas Jathar
    (This message was posted on behalf of Intel Corporation)

  5. #5
    Join Date
    Apr 2018
    Posts
    11
    Rep Power
    1

    Default Re: Progress FAILED !!! on the programmer.

    I exercised your steps but the error occur.
    I add attachements, can u look it ?
    Why did the error occur?

    Does my cable be imcompatible ?
    Thank u ...
    Attached Images Attached Images

  6. #6
    Join Date
    Feb 2018
    Posts
    75
    Rep Power
    1

    Default Re: Progress FAILED !!! on the programmer.

    Hi,
    Install the Intel FPGA Download Cable II since your screenshot showing Altera USB-blaster II unconfigured, Refer the following link,
    https://www.altera.com/documentation...847781805.html
    Try using another USB-Blaster II download cable as well.

    Best Regards
    Vikas Jathar
    (This message was posted on behalf of Intel Corporation)

  7. #7
    Join Date
    Apr 2018
    Posts
    11
    Rep Power
    1

    Default Re: Progress FAILED !!! on the programmer.

    Quote Originally Posted by jatharvk View Post
    Hi,
    Install the Intel FPGA Download Cable II since your screenshot showing Altera USB-blaster II unconfigured, Refer the following link,
    https://www.altera.com/documentation...847781805.html
    Try using another USB-Blaster II download cable as well.

    Best Regards
    Vikas Jathar
    (This message was posted on behalf of Intel Corporation)

    Thank u for helping me ;
    But My computer's software is windows 10, I can try your exercises but I am looking the website for USB Blaster II, IT İS NOT SUPPORTED
    Windows 10
    ı think It occur the error because of software , doesn't it ???

  8. #8
    Join Date
    Jun 2007
    Location
    Weikersheim, Germany
    Posts
    286
    Rep Power
    1

    Default Re: Progress FAILED !!! on the programmer.

    Well I have even the USB-Blaster (not the newer USB-Blaster II) running under Windows10. I just went to device manger, right click on the device, update driver, use driver on computer, point to the driver directory of the Quartus II Installation. That worked pretty well :-)

  9. #9
    Join Date
    Apr 2018
    Posts
    11
    Rep Power
    1

    Default Re: Progress FAILED !!! on the programmer.

    Thank u I will try it that is your actions
    I hope , it will work

Similar Threads

  1. Replies: 9
    Last Post: July 11th, 2017, 11:56 PM
  2. Cpld Programmer - Progress %98 failed
    By mustafayilmaz in forum General Altera Discussion
    Replies: 1
    Last Post: November 20th, 2016, 08:52 AM
  3. EP4CE75 programmer : verification failed for device number 1
    By cky in forum FPGA, Hardcopy, and CPLD Discussion
    Replies: 0
    Last Post: January 20th, 2016, 05:04 PM
  4. Cyclone IV Programmer Failed
    By rgPaiva in forum FPGA, Hardcopy, and CPLD Discussion
    Replies: 0
    Last Post: May 16th, 2012, 04:52 PM
  5. nios2-flash-programmer failed!
    By lameck in forum FPGA, Hardcopy, and CPLD Discussion
    Replies: 0
    Last Post: September 6th, 2010, 02:40 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •