Results 1 to 4 of 4

Thread: Problem with compiling Quartus project: Working project is not working any more

  1. #1
    Join Date
    Jul 2018
    Posts
    8
    Rep Power
    1

    Unhappy Problem with compiling Quartus project: Working project is not working any more

    Hi all,
    I am facing a problem that is not going away in any way.
    The problem is when ever I compile my design it gives the following error:

    Can't place 37 pins with 2.5 V I/O standard because Fitter has only 32 such free pins available for general purpose I/O placement.

    Well, I have changed few banks to other voltages. Then it begins to complain about other voltages, the same way.
    I am following a tutorial and using their ready made .csv file for pin assignment(importing .csv file).
    This project involves creation of schematic and generation of a Qsys system and then placing the symbol of Qsys system(NIOS II processor) in the schematic.

    It worked very fine for few days. Then I changed the Qsys file(according to the part 2 of the lab), and then it stopped working all together(failing to compile since than.

    Till part 1 of the lab it was working fine.
    So I again started project (lab 1) many times, but even lab 1 is not working now, and same fitter problem. Please see the attached file also.
    Should I clean things on system level? if yes, then which files should be deleted or option should be changed.
    Any body any guess?
    Attached Images Attached Images
    Last edited by TAHIRSENGINE; July 12th, 2018 at 01:16 AM. Reason: to better explain my problem

  2. #2
    Join Date
    Jul 2018
    Posts
    8
    Rep Power
    1

    Default Re: Problem with compiling Quartus project: the fitter problem

    Please note that I am using Quartus 16.1

  3. #3
    Join Date
    May 2013
    Posts
    908
    Rep Power
    1

    Default Re: Problem with compiling Quartus project: Working project is not working any more

    The picture is not legible.

    Are you still getting the same error? In the Pin Planner, do manual pin assignments instead of just letting the Fitter do it.

  4. #4
    Join Date
    Jul 2018
    Posts
    8
    Rep Power
    1

    Default Re: Problem with compiling Quartus project: Working project is not working any more

    The picture is not legible.

    Are you still getting the same error? In the Pin Planner, do manual pin assignments instead of just letting the Fitter do it.

Similar Threads

  1. Quartus Fitter Crashes (Prime Pro 16.1.0) when compiling for Arria 10 SOC
    By datkins in forum FPGA, Hardcopy, and CPLD Discussion
    Replies: 1
    Last Post: December 29th, 2016, 03:52 AM
  2. Quartus Prime 16.0 stops compiling before fitter runs
    By ghogerheiden in forum Quartus II and EDA Tools Discussion
    Replies: 6
    Last Post: June 15th, 2016, 04:30 PM
  3. Problem when compiling project in Quartus 13.0
    By NguyenNgocTan in forum Quartus II and EDA Tools Discussion
    Replies: 1
    Last Post: November 13th, 2014, 05:36 AM
  4. MAX+PLUS II project not compiling in Quartus II 7.2---
    By nuzrajesh1 in forum General Altera Discussion
    Replies: 3
    Last Post: July 1st, 2013, 11:41 PM
  5. Quartus II compiling/simulating problem
    By tyler in forum Development Kit Related
    Replies: 6
    Last Post: January 27th, 2009, 09:19 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •